كيف هل أنا استخدام أ متعدد إلى حدد أ الطاقة الإمداد ل بلدي الكمبيوتر٪ 3f
اختر أ قوي قلب - كيف إلى استخدام أ متعدد إلى اختر أ كمبيوتر طاقة إمداد٪ 3f في الوقت الحاضر٪ 2c الجديد جيل من الرسومات البطاقات٪ 2c الصوت البطاقات٪ 2c بصري محركات الأقراص ٪ 2c الصلب محركات الأقراص و أخرى الملحقات في الطاقة الاستهلاك من أي شخص هو لا an النفط مصباح . متى أنت الحب الآلة محشوة ممتلئة من الدهون الدماغ متى لديك من أي وقت مضى فكر من هو مع أ قوي القلب.
تشغيل ال تحديد من الطاقة الإمداد طرق من الصحف و المجلات لديها كان أ الكثير من القريدس على النظرية ٪ 2c جمعت أعلى تقريبا ثلاثة٪ 3a
A نظرة - نظرة في ال الطاقة العرض المواد هو غرامة ٪ 2c ما إذا كان غرامة صنعة ٪ 2c تخطيط هو معقول. بصراحة يتحدث ٪ 2c هذا البرنامج هو أكثر أو أقل صعب. أول من الكل٪2c it يتطلب the التنفيذ of كافية إلكترونية المعرفة٪3b ثانيا٪2c to see the power supply of the five viscera and six lungs بشكل شامل حقا have to open the power supply cover shell can not be٪2c which will حتمي destroy the business warranty seals٪2c seals a bad automatically lose the business warranty٪2c even if the power supply has problems have to DIY. I think a lot of normalry المبتدئين هم لذلك يائسة٪ 2C ميؤوس منها قسري في القريدس.
الثانية اللمس - يشير إلى الطاقة الإمداد المروحة بعد أ الفترة من الوقت إلى اللمس الطاقة الإمداد المروحة النفخ الخروج من ال الرياح هو ساخن٪ 2c سواء الغطاء هو ساخن.
ثلاثة رائحة - رائحة قوة إمداد في أ أطول فترة من وقت بعد عمل ما إذا كان هو سوف ينبعث أ محترق رائحة. الأخير اثنان هي بحتة إدراكية تجربة تراكم٪ 2c ال مبتدئ لديه لا خبرة إلى يتكلم من و كيف إلى جعل أ الحكم٪ 3f هنا ٢ ج أنا أوصي أ متعدد إلى القاضي القوة العرض جيد أو سيئ طريقة٪ 2c ربما من أجل مبتدئين إلى توفير بعض مساعدة.
First of all, of course, is to find a multimeter (preferably digital), and will have to use the multimeter. aTX power supply voltage provided by the main 3.3V, 5.0V, 12.0V several kinds of which 12.0V is the main energy to drive the work of the hardware equipment, in the connection with more loads after the change is also * obvious, so in the connection with all the loads of the computer, any choice of a free output head, the black pen into the black line interface, the red pen into the yellow line interface (the purpose is to detect the 12V output voltage). Connected to the plug connector can be switched on after the test. After powering on the multimeter, we can find that the multimeter data is constantly changing, until the system is completely started to stabilise. Note down the value of the voltage at this time, it should be in the normal 12V or so (about 11.95V to 12.15V, too low to ensure stable operation of large loads for long periods of time, and there is no potential for expansion, too high and will make the device heat, premature aging).
Then press rESET to restart the machine. At this time to keep a close eye on the value of the multimeter changes, boot self-test when the multimeter value will reach its lowest point. Note down the voltage value at this time. If the voltage difference between the highest value and the lowest value is not too large (within 0.3V), the power supply is acceptable. If the voltage difference is too large, it means that the power supply load capacity is poor, should not be selected. I have personally encountered a 300W power supply whose highest value was 12.32V but the lowest was only 11.73V, and it frequently crashed when in use. Finally, observe the situation in use. Run all kinds of software, and then use the CD-ROM drive to listen to music, so that all parts of the machine are operating. Pay attention to the voltage at this time, if there is no obvious fluctuation then it can be selected.
